Sensormatic SpeedDome Ultra IV Manual del operador Pagina 38
- Pagina / 76
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Alarms, Areas and Home Settings 4-11
6. Repeat steps 4 and 5 for each area you want to establish.
Note: You will see the following error message under certain conditions:
Error programming areas
Focus Far to continue.
• If you attempt to program a boundary that passes the starting point of the first area
• If you move the camera left after establishing the first boundary
Return to step 1 and start again.
7. When the last area boundary is set, press Focus Far.
The following confirmation message appears:
Areas saved successfully
Focus Far to continue.
Press Focus Far to continue.
8. When the Alarms/Areas/Home screen appears, do one of the following:
• If you want to configure the alarm actions, continue with Configuring Alarm
Actions on page 4-2.
• If you want to configure the input states, continue with Configuring Normal
Input States on page 4-5.
• If you want to set the “home” position, continue with Assigning the Dome’s
Home Position on page 4-7.
• If you are finished making changes, press and hold Iris Close, then press Focus
Near or Focus Far to save your changes and exit the utility.
5
• If you want to make changes to other settings, use the Tilt control to move the
highlight bar to Exit, then press Focus Far. The Dome Configuration Menu
appears. Continue with What To Do Next found on page 4-13.
Programming Presets
A preset is a programmed video scene with automatic pan, tilt, zoom, focus and iris settings.
Presets may be assigned to alarm actions or as the “home” position for the dome. Up to 96
presets whose positions are saved in the domes firmware may be programmed. Domes
installed in SensorNet or RS-422 networks support up to 96 presets. Domes installed in
Manchester networks support up to 64 presets. If you attempt to program a preset numbered
higher than 64 in a Manchester network, the controller beeps.
VM96 and AD matrices installed as RS-422 and SensorNet networks support “virtual” views.
This means that the pan, tilt, zoom, focus, and iris settings are stored within the controller,
not the dome. You cannot use the views that you define on those systems as the home
position or an alarm action. You must use the presets programmed using this utility.
5
This command is not supported with Manchester.
- Configuration Utility 1
- O perator's M anual 1
- SpeedD om e 1
- U ltra IV 1
- Cam era Dom e 1
- SpeedDome 2
- Ultra IV 2
- Table of Contents 4
- Before You Begin 6
- What’s In This Manual? 7
- Text Conventions 7
- Related Documents 8
- Getting Help 8
- Getting Started 9
- 1-2 Operator's Manual 10
- Exiting the Utility 11
- Password Protection 12
- Restoring Factory Settings 13
- Where To Go Next 14
- Keeping Records 14
- Pan, Tilt, and Zoom Options 15
- Highlight Bar: 16
- Move with Tilt 16
- Setting the Zoom Stop Factors 17
- The default setting is 64X 18
- What To Do Next 19
- Camera and Lens Functions 20
- Setting Line Lock 21
- The default setting is On 22
- Setting the AGC Mode 23
- (purple) 24
- Camera and Lens Functions 3-7 26
- CHAPTER 4 28
- Configuring Alarm Actions 29
- 4-4 Operator’s Manual 31
- IMPORTANT 32
- Setting Normal Input States 33
- Setting the Home Position 34
- 4-8 Operator’s Manual 35
- Programming Area Boundaries 36
- 4-10 Operator’s Manual 37
- Programming Presets 38
- 4-12 Operator’s Manual 39
- 4-14 Operator’s Manual 41
- CHAPTER 5 42
- ZOOM X18D 43
- AUTO IRIS ON/OFF 43
- AUTO FOCUS ON/OFF 43
- The default setting is Off 44
- ALARM NAME 45
- AREA NAME 45
- CAMERA NAME 45
- PATTERN/PRESET NAME 45
- Setting Names 48
- 5-8 Operator’s Manual 49
- NAME PROGRAMMING 50
- PATTERN 1 50
- NAME: MAIN LOBBY SOUTH 50
- UNDO CHANGES AND QUIT 50
- TEXT ATTRIBUTE OPTIONS 51
- CHARACTER OUTLINE 51
- TRANSLUCENT NAMES OFF 51
- CHARACTER OUTLINE OFF 52
- TRANSLUCENT NAMES OFF 52
- TRANSLUCENT NAME 52
- CHAPTER 6 54
- Selecting a Language 55
- Working with Passwords 57
- APPENDIX A 60
- Name Configuration 62
- A-4 Operator’s Manual 63
- Appendix A: Records A-5 64
- A-6 Operator’s Manual 65
- Software License Agreement 66
- SOFTWARE LICENSE AGREEMENT 67
- B-4 Operator's Manual 69
- Glossary 70
- G-2 Operator's Manual 71
- Glossary G-3 72
- 8000-2612-01 76
Relacionado con productos y manuales para Cámaras De Seguridad Sensormatic SpeedDome Ultra IV
(42 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales